If you setting hex values correct format is:
snmpset($source_ip,$community,"$oid","x","10 10 10 10");
(PHP 4, PHP 5, PHP 7, PHP 8)
snmpset — Define o valor de um objeto SNMP
$hostname
,$community
,$object_id
,$type
,$value
,$timeout
= -1,$retries
= -1
snmpset() é usado para definir o valor de um objeto SNMP
especificado pelo object_id
.
hostname
O nome do host do agente SNMP (servidor).
community
A comunidade de escrita.
object_id
O ID do objeto SNMP.
type
O MIB define o tipo de cada ID de objeto. Deve ser especificado como um único caractere da lista abaixo.
= | O tipo é retirado do MIB |
i | INTEGER |
u | INTEGER |
s | STRING |
x | HEX STRING |
d | DECIMAL STRING |
n | NULLOBJ |
o | OBJID |
t | TIMETICKS |
a | IPADDRESS |
b | BITS |
Se OPAQUE_SPECIAL_TYPES
foi definida ao compilar a biblioteca SNMP, os seguintes tipos também são válidos:
U | unsigned int64 |
I | signed int64 |
F | float |
D | double |
A maioria destes tipos usará o tipo ASN.1 correspondente óbvio. 's', 'x', 'd' e 'b' são todas maneiras diferentes de especificar um valor OCTET STRING e o tipo sem sinal 'u' também é usado para lidar com valores Gauge32.
Se os arquivos MIB forem carregados na árvore MIB com "snmp_read_mib" ou ao especificar isso na configuração da libsnmp, '=' pode ser usado como
o parâmetro type
para todos os IDs de objeto, pois o tipo pode ser lido automaticamente a partir do MIB.
Note que existem duas maneiras de definir uma variável do tipo BITS como, por exemplo, "SYNTAX BITS {telnet(0), ftp(1), http(2), icmp(3), snmp(4), ssh(5), https(6)}":
Consulte a seção de exemplos para obter mais detalhes.
value
O novo valor.
timeout
O número de microssegundos até o primeiro tempo limite.
retries
O número de tentativas caso ocorram tempos limite.
Retorna true
em caso de sucesso ou false
em caso de falha.
Se o host SNMP rejeitar o tipo de dado, uma mensagem E_WARNING como "Warning: Error in packet. Reason: (badValue) The value given has the wrong type or length." será exibida. Se um OID desconhecido ou inválido for especificado, o aviso provavelmente será "Could not add variable".
Exemplo #1 Usando snmpset()
<?php
snmpset("localhost", "public", "IF-MIB::ifAlias.3", "s", "foo");
?>
Exemplo #2 Usando snmpset() para definir um ID de objeto SNMP BITS
<?php
snmpset("localhost", "public", 'FOO-MIB::bar.42', 'b', '0 1 2 3 4');
// ou
snmpset("localhost", "public", 'FOO-MIB::bar.42', 'x', 'F0');
?>
If you setting hex values correct format is:
snmpset($source_ip,$community,"$oid","x","10 10 10 10");
The "type" parameter must be one of the following, depending on the type of variable to set on the SNMP host:
i INTEGER
u unsigned INTEGER
t TIMETICKS
a IPADDRESS
o OBJID
s STRING
x HEX STRING
d DECIMAL STRING
n NULLOBJ
b BITS
If OPAQUE_SPECIAL_TYPES was defined while compiling the SNMP library, the
following are also valid:
U unsigned int64
I signed int64
F float
D double
As an example, using "i" would set an integer, and "s" would set a string. If the SNMP host rejects the data type, you might get the following message: "Warning: Error in packet. Reason: (badValue) The value given has the wrong type or length."
If you specify an unknown or invalid OID, you might get a "Could not add variable" message. When specifying an absolute OID (one that is already resolved) that is completely numeric, prepend it with a period. For example, an OID that could enable/disable Ethernet ports on an Asante hub might be "1.3.6.1.2.1.22.1.3.1.1.3.6.4.0", but you would need to use ".1.3.6.1.2.1.22.1.3.1.1.3.6.4.0" in the OID parameter so that the SNMP library won't try to resolve an already resolved OID. Friendly, unresolved OIDs do not need the period prepended, such as "system.SysContact.0"
Note that there are two ways to set a variable of the type BITS like e.g.:
SYNTAX BITS {telnet(0), ftp(1), http(2), icmp(3), snmp(4), ssh(5), https(6)}
1. Using type "b" and a list of bit numbers like:
snmpset('FOO-MIB::bar.42', 'b', '0 1 2 3 4');
with the disadvantage that the success is not easily verifyable as an snmpget() for the same OID would return e.g. 0xF8.
2. Using type "x" and a hex number but without(!) the usual "0x" prefix:
snmpset('FOO-MIB::bar.42', 'x', 'F0');